Link-systems 5100-8 Tonnage & Analog Signal Monitor Uživatelský manuál stáhnout pdf (Strana 6)

Doc #: L-802-1110 Page 4 Rev. 02

Table of Figures

Figure 1: Example Die 1 with Signature..................................................................................................... 8

Figure 2: Example Die 2 with Signature..................................................................................................... 8

Figure 3: Example Data Window ............................................................................................................... 9

Figure 4: Operator Terminal Main Screen................................................................................................ 13

Figure 5: Tonnage Monitor Main Screen Showing Peak Forward Tonnage............................................ 14

Figure 6: Tonnage Monitor Main Screen Showing Data Window 1 Tonnage......................................... 17

Figure 7: Tonnage Monitor Main Screen Showing Reverse Tonnage ..................................................... 18

Figure 8: Tonnage Monitor Diagnostic Screen......................................................................................... 27

Figure 9: Tonnage Monitor Bypass Setup Screen .................................................................................... 29

Figure 10: Example Tonnage Waveform with Peak Settings Selected for View..................................... 30

Figure 11: Example Waveform with Data Window 2 Settings Selected for View .................................. 33

Figure 12: Example Tonnage Waveform in Pan/Zoom Mode.................................................................. 35

Figure 13: Graph Settings Screen ............................................................................................................. 40

Figure 14: Device Config Screen.............................................................................................................. 42

Figure 15: Tonnage Monitor Device Configuration Screen ..................................................................... 43

Figure 16: Tonnage Configuration Screen................................................................................................ 43

Figure 17: Tonnage Monitor Machine Settings Screen............................................................................ 44

Figure 18: Tonnage Monitor Calibration Screen...................................................................................... 47

Figure 19: Example Tonnage De-rate Curve............................................................................................ 48

Figure 20: Tonnage Monitor Total Capacity De-rate Screen ................................................................... 49

Figure 21: Unit Mounting Dimensions..................................................................................................... 51

Figure 22: Tonnage Monitor Faceplate..................................................................................................... 52

Figure 23: Power Connector..................................................................................................................... 53

Figure 24: System 5000 High Speed Bus Wiring..................................................................................... 53

Figure 25: Automation Control High Speed Bus Wiring ......................................................................... 53

Figure 26: High Speed Serial Bus Connector........................................................................................... 54

Figure 27: Termination Switch................................................................................................................. 54

Figure 28: “C” Frame Machine Gage Locations ...................................................................................... 55

Figure 29: Straight Side Machine Gage Locations................................................................................... 56

Figure 30: Upright Areas to Avoid........................................................................................................... 56

Figure 31: Solid Frame Machine Gage Locations.................................................................................... 57

Figure 32: Strain Gage Drill Fixture......................................................................................................... 58

Figure 33: LST-1000 Strain Gage Mounting............................................................................................ 58

Figure 34: Weld Pad Mounting Fixture.................................................................................................... 59

Figure 35: Weld Pad Welding Technique................................................................................................. 59

Figure 36: Strain Gage Wiring.................................................................................................................. 60

Figure 37: Load Cell Hit with Bad Tie-Rod Tension ............................................................................... 68

Figure 38: Load Cell Hit with Good Tie-Rod Tension............................................................................. 68

Figure 39: 5100-8 Circuit Board Option Connectors ............................................................................... 69

Figure 40: 5100-8 Main Circuit Board With 5100-8A Option Board ...................................................... 70

Figure 41: 5100-8 Main Circuit Board With 5100-8C Option Board ...................................................... 71

Figure 42: 802-5B Solid State Relay Board Dimensions ......................................................................... 72

Figure 43: 802-5B Solid State Relay Board Connections ........................................................................ 73

Figure 44: Example Text Entry................................................................................................................. 79

Figure 45: Example Password Entry Sequence ........................................................................................ 82

1 2 3 4 5 6 7 8 9 10 11 ... 85 86

Komentáře k této Příručce

Žádné komentáře

Link-systems 5100-8 Tonnage & Analog Signal Monitor Uživatelský manuál Strana 6

Komentáře k této Příručce

Související produkty a manuály pro Měřící nástroje Link-systems 5100-8 Tonnage & Analog Signal Monitor